Search results

  1. K

    Camshaft sprocket holding tool?

    On ebay I found just the locking tool. It's from Kent Moore and has the same part number. It's going for around $30 to $40, so I'll just get the ebay one. Thanks.
  2. K

    Camshaft sprocket holding tool?

    Has anyone used the Kent Moore J-43655 camshaft tool on any newer L61 engine besides the 2002 L61? I will be doing some head work on my 2007 2.2L and this tool is what I need to get the job done.
  3. K

    Comp Cams cam grind XE252HR-11, part number 113200

    I'll probably just do a cylinder head rebuild because that is where my problem lies.
  4. K

    Comp Cams cam grind XE252HR-11, part number 113200

    Building the motor to boost it is out of my budget.
  5. K

    Has anyone done a 2007 2.2 engine swap?

    I live in Phoenix, AZ, and called Engine House for a quote on a rebuild of my engine. They quoted me around $2,000 for an ecotec long block. This is too much, so I'm deciding on an engine swap. Has anyone done a swap for a 2007 cobalt?
  6. K

    Comp Cams cam grind XE252HR-11, part number 113200

    I have a 2007 2.2 ls cobalt. I recently asked Gabriel Ray from Comp Cams about cam grind XE252HR-11, part number 113200. I have 13xxxx miles on my cobalt and it runs like crap. I've also tried fixing it but the dang thing keeps running like crap. On top of that my cv axle on the driver side...
  7. K

    Balance shaft TDC position?

    When timing your cam sprockets do you have to reset timing on the balance shafts too?
  8. K

    How do you take off CV axle if its stuck in transmission?

    Bfh?
  9. K

    How do you take off CV axle if its stuck in transmission?

    I know how to get to the cv axle and know how to take it off but the dang thing just doesn't want to come out. We even tried tying a come-a-long to it and it still won't come out. We even heated up the shaft just like the video and it still doesn't want to come out. Next option was going to...
  10. K

    How do you take off CV axle if its stuck in transmission?

    My CV axle boot is torn and won't come out of the transmission. Has this happened to anyone if so any info on how to take it out would be greatful.
  11. K

    Is there an alignment tool for intake cam?

    Do you also have to time the balance shaft chain with it too?
  12. K

    Is there an alignment tool for intake cam?

    The intake cam on the 2.2 is a little longer than the exhaust so is the extra length for the cam sensor or is it used for an alignment tool. Asking this question because some DOHC engines require an alignment tool plus a cam locking tool. My motor is giving me a hard time and I would hate to...
  13. K

    Which heads are better the GMPP or Patriot?

    Any specific measurements on head porting for bolt on mods?
  14. K

    Which heads are better the GMPP or Patriot?

    Does anyone know which head is better?
  15. K

    How do you re-time a 2007 2.2 cobalt?

    How do you re-time a 2007 2.2L cobalt after completing a valve job?
  16. K

    where do you get a cam holding tool in phoenix, AZ?

    Didn't have the tool when I changed the exhaust valve so I used a marker.
  17. K

    where do you get a cam holding tool in phoenix, AZ?

    Changed exhaust valve, need to be set back to top dead center. Chain timing marks didn't match with cam gear timing marks when installing it.
  18. K

    where do you get a cam holding tool in phoenix, AZ?

    I have a 2007 ls cobalt and need a camshaft holding tool for the 2.2 engine. I live in Arizona so I was hoping to buy locally. OTC has the right tool for the job but they don't sell it online. Anyone know where to get that specific specialty tool?
  19. K

    How do you take off driver side door panel?

    Driver side window shattered and need to know how to take off driver side door panel. Any info would be appreciated and if there are any special tools I need to know about that would make the job easier or if it can be done with just simple hand tools. The vehicle is a 2007 cobalt LS 2 door coup.
  20. K

    trouble code P0340.

    Scratch the camshaft positioning sensor just installed a new one and the CEL light is still lit so the sensor is not the problem.
  21. K

    trouble code P0340.

    When all work was being done the battery was disconnected. When starting it up after valve replacement engine light was not lit but after shutting it down and starting it back up the light lit up again. I also disconnected the battery and disconnected the ECM on all 3 connections and...
  22. K

    trouble code P0340.

    No mods just replacing valves. Valves were melted and needed replacment.
  23. K

    trouble code P0340.

    I have a 2007 chevy cobalt 2.2L. I went to autozone and got the code checked out and it was the camshaft positioning sensor. A while back when I changed both exhaust valves for the number 1 cylinder I notice that the camshaft positioning sensor reads off the intake camshaft. When assembling...
  24. K

    2.2 to 2.4 manifold

    What do u need in order to swap the 2.2 intake manifold to a 2.4 intake manifold? And when swaping over manifolds does the 2.4 intake still accept the stock throttle body from the 2.2 and other connections like a K&N intake. Thanks and any further info would be helpful.
  25. K

    cobalt ss transmission swap to LS model

    Can the ss model transmission be swaped over to the L61 engine on the LS cobalt model?

Members online

Total: 288 (members: 1, guests: 287)

Forum statistics

Threads
7,432
Posts
156,463
Members
4,339
Latest member
KaiAnderso

Latest posts

Top